The BNC connector is a connector type, quick connect/disconnect, incoporando more security connector for coaxial cable. Initially designed as a miniature BNC Connector Type C is a type of connector used with coaxial cables like RG-58 and RG-59 RF applications that required a quick connector, suitable for UHF and constant impedance to over a wide range.

The DIN is a standard that was developed by the "Deutsches Institut für Normung" (one might call the national standards organization in Germany). The DIN is facing many sectors, but we have tried to focus on the DIN-oriented electronics and computing. In the case of Enclosures means qualifying under the German legislation on racks and is standardized to DIN 41494-7.

A DIN Rail is a metal rail of with standard size of 35 mm wide. (A)

It's commonly used on installation and assembly of electrical devices or controllers for home or business use.
Besides the typical DIN rail 35 mm x 7.5 mm, can also be found in other measures as:

- Mini DIN Rail, size 15 mm x 5.5 mm (B)
- DIN Rail, size 35 mm x 15 mm (C)
- G section, size 32 mm x 15 mm x 8mm (D)

These rails are designed for installations with a method of simple, fast and configurable fixing. Ideal for installation in electrical distribution points, distribution of telephone wiring, alarms, digital electric programmers, keystone adapter, attenuators and any other compatible device.

When we talk about RJ45 ("Registered Jack" 45) we refer to a telecommunications network interface for wired connection of voice and data equipment.

This connector has 8 pins or connections and may have a specific category depending on the data transfer speed and bandwidth (category 5e, 6, etc.)

The common application is their use in Ethernet network cables under TIA/EIA-568-B standard that defines the arrangement of pins (pinout), but can also be used for other applications.

- Direct pin diagram:

EIA-568A
Pin No.1: WHITE-GREEN
Pin No.2: GREEN
Pin No.3: WHITE-ORANGE
Pin No.4: BLUE
Pin No.5: WHITE-BLUE
Pin No.6: ORANGE
Pin No.7: WHITE-BROWN
Pin No.8: BROWN

EIA-568B
Pin No.1: WHITE-ORANGE
Pin No.2: ORANGE
Pin No.3: WHITE-GREEN
Pin No.4: BLUE
Pin No.5: WHITE-BLUE
Pin No.6: GREEN
Pin No.7: WHITE-BROWN
Pin No.8: BROWN

- Schematic of crossed pins:

The crossover cable has one end with EIA-568A scheme and the other one with EIA-568B.

Depending on the quality and type, network cables are classified into categories that help us know the characteristics of them.

The categories of network cables most commonly used are:

- Category 5
- Category 5e
- Category 6
- Category 6
- Category 7

As can be seen, category 5e (enhanced or improved) and category 6A (Augmented), are an improvement of categories 5and 6, respectively, which it has improved the top speed and bandwidth.

The higher the category, the higher the speed of maximum data, the maximum 100 meters distance as its standard.

You can see a table which shows the 5 categories, where V is the maximum velocity, D is the maximum and MHz frequency which can work away.

The RCA (Radio Corporation of America) connector is a connector used to send video signals or audio.
This is a circular two-contact connector; signal and ground, used with coaxial cables. Each signal uses a single cable and to differentiate color coded RCA connector on the set.
(1) Analog Audio:
Audio Left (White)
Audio Right (Red)

(2) Videoanalogical:
Video (Yellow)

(3) Composite Video:
Audio Left (White)
Audio Right (Red)
Video (Yellow)

(4) Video Component (YPbPr):
Y (Green)
Pb (Blue)
Pr (Red)

(5) Video components (RGB):
R (Red)
G (Green)
B (Blue)

(6) Digital Audio:
S/PDIF (Orange/Gold)

It is called TB110 or terminal block 110 to the type of block system for the connection of certain wiring systems, such as in network installations, typical connector used in most patch panels.

The denomination 110 refers to the type of encapsulation available to the connectors, a crimp system that needs to press the connection cable downwards.

One of the advantages of this type of connectionres is its small size, guaranteeing more connectors in less space.

This type of connector requires a special tool, called an impact tool, which performs two functions at the same time.

Once the cables are placed in their corresponding positions we will use the crimping tool pressing down with the side of the blade on the outside, thus getting to press the cable towards abajo, crushing it, in turn the blade will cut the excess wire.