IEC connector is the common name for a set of thirteen power connectors (called the connector specifications) and thirteen outlet panels (called input) specification defined by IEC 60320 (formerly IEC 320) of the International Electrotechnical Commission ( IEC). When used without other qualifiers, "IEC connector" usually refers specifically to the C13 and C14 connectors.

In IEC connector or cable with a base (usually plastic) and a plug to connect to the socket (plug), if we put these two things we would get the named SCHUKO is the overall connector. The schuko not determine the type of connector. It would be determined by the specification of the International Electrotechnical Commision (IEC). We leave a small sample of Schukos internationally.

When carrying out an electrical installation or electrical circuit several factors must be taken into account, one of them is the selection of the appropriate cable. According to the installation and the use of the same we can find different diameters that support different loads. The cable section will also help us not to overheat our installation, since the larger the section, the greater the thermal resistance.
In the following table poWe can see the corresponding load supported for the different sections of cables.

As it is common in installations we can find a standard of colors in the electric cables.

These regulations help at a glance to understand the connection and the resolution of possible faults or failures.

Below we attach the color/cable relation for electrical installations.

1. The ground wire can be identified in several ways:
• Green cable.
• C cablegreen smell with a yellow line.
• Cable without insulation.
2. The neutral wire will be blue.
3. The phase cable can be identified in several ways:
• Any color different from neutral or earth.
• Black insulation.
• Brown isolate.
• Gray insulation.

The insulating or insulating tape is a fundamental element when making a repair or performing an electrical installation. The insulating tape will help us to protect and insulate the electrical cables from possible crossings or contacts between them or with other elements, guaranteeing that the connection is well insulated avoiding possible short circuits.
Its use is very simple, since being a flexible material allows us to apply it with comfort.
To achieve a perfect union, it is recommended that we wrap the tape covering half the cable and half over the joint, stretching the tape slightly while rolling obliquely.

• For the ground wire, colored insulation tape will be used:
• Green.
• Green with a yellow line.
• For the neutral cable, blue insulating tape will be used.
• For the cable the phase isYou can use any other color:
• Any color different from neutral or earth.
• Black insulating tape.
• Brown insulating tape.
• Gray insulating tape.

VAC would be the abbreviation of Volt Altern Current which would be translated Volts of alternating current. The difference between VDC is that its sinusoidal oscillation achieving a more efficient energy transmission.

The alternating current is the energy that we receive in our homes, it is generated in the power plants by means of alternators.

The intensity of this type of current varies with time, and changes direction 50 times throughsecond (50hz). The generated voltage changes in the form of sine wave so it is not constant.

In the image:

1. Current by pulsations.
2. Direct current (DC).
3. Alternating current (AC).
4. Variable current.

One of the basic components in most electrical circuits or electrical installations are the fuses, the fuse is a capsule (B) that has metal ferrules (C) on its ends, in which a thin filament of alloy or metal (A) characterized by having a low melting point.
The fuse is placed in a specific point of the installation, and will serve to protect said installation frompossible damage due to electrical overload or voltage.
In their normal state the filaments have continuity at their ends (C, D). This over voltage causes this filament to heat up and break (C.1, C.2), not passing electrical energy and protecting the circuit while minimizing the risk of fire.

We can find all kinds of fuses, according to their amperage, design etc.
Among the most common we can findr:

• Cylindrical fuse glass material. They are usually used in most household appliances, power supplies, etc.
• Fuses for Blade vehicles. They are the fuses that protect the electrical installation of the vehicle, usually they are of the same type and design in most vehicles, according to their amperage they have a specific color.
• Brown = 5 A
• Red = 10 A
• Blue = 15 A
• Yellow= 20 A
• Colorless = 25 A
• Green = 30 A
• Fuses for mini vehicles: It is the same as the previous one but of a smaller size.
• Fuses for Maxi vehicles: It is the same as the previous one but of a larger size.
• Midi Fuses
• Mega Fuses
• Reed fuses
• High voltage or industrial fuses

Your symbol is represented as a box and a line that crossesA line or a line is a sinusoidal shape (E).