An uninterruptible power supply, UPS, also known as UPS (uninterruptible power supply English), is a device that, thanks to batteries or other energy storage elements, can provide power for a limited time and for a blackout all the devices connected. Other features that can be added to these teams is to improve the power qualityéctrica reaching loads, ups and downs filtering and eliminating voltage harmonics of the network in the case of using AC. There are different types of UPS UPS DC loads connected to the UPS require DC power, so they will transform the alternating current to direct current sales network and use it to power the load and store it in your batterys. So they do not require converters between the batteries and loads. UPS AC UPS obtained These outputs an AC signal, so they need an inverter to convert the direct signal from the batteries in an alternating signal. UPS standby (Standby Power Systems) This system has two main circuits: the power line, which only addsa stabilized and additional filtering of each team to normal feed, and the actual circuit UPS circuit whose core is called "inverter". It is called system "standby" or waiting, because the circuit of alternative power, the inverter is "offline" or inactive, waiting to become operational when it produces a failure in the power supply. It has a switching element that connectsand either circuit switched alternately. UPS line-interactive (in-line) This type of UPS regulates voltage variations by elevations or reductions in mains voltage. During these interventions, the UPS uses its battery to perform the voltage regulation. UPS online (online) In contrast, the UPS "online" (on-line), the battery and the inverter are permanently It is utiized, ensuring a maximum response in a timely manner before the event of network failure. In addition, they can also correct the frequency shifts as re-generate the ac wave permanently. Diagram UPS online In the picture (1) Rectifier The picture (2): battery in the picture (3): Inverter

IEC connector is the common name for a set of thirteen power connectors (called the connector specifications) and thirteen outlet panels (called input) specification defined by IEC 60320 (formerly IEC 320) of the International Electrotechnical Commission ( IEC). When used without other qualifiers, "IEC connector" usually refers specifically to the C13 and C14 connectors.

In IEC connector or cable with a base (usually plastic) and a plug to connect to the socket (plug), if we put these two things we would get the named SCHUKO is the overall connector. The schuko not determine the type of connector. It would be determined by the specification of the International Electrotechnical Commision (IEC). We leave a small sample of Schukos internationally.

The BS-1363-1 format is the standard format British plug. It has a very significant carasterística in the upper plug and the existence of a fuse. The old format English was the BS-546

When carrying out an electrical installation or electrical circuit several factors must be taken into account, one of them is the selection of the appropriate cable. According to the installation and the use of the same we can find different diameters that support different loads. The cable section will also help us not to overheat our installation, since the larger the section, the greater the thermal resistance.
In the following table poWe can see the corresponding load supported for the different sections of cables.

Within the different types of electrical cables we can find single or multifilament cables. The difference lies in the number of conductors that make up the cable. Single wire cables contain only a single conductive wire, whereas multi-wire cables contain more than one wire. Do not confuse multifile (A) or single wire (B) with monopolar (C), bipolar (D) or multipolar (E) cable. Monopolar cables have only oneSingle conductor, bipolar cables have two conductors, while multi-pole cables have more than two conductors. It may be said that any unipolar, bipolar or multipolar cable can be single-ended or multi-stranded. In the case of single wire cables we will talk about rigid cables, whereas the multifilament cables will be flexible.
In the following table you can see the difference between them.

As it is common in installations we can find a standard of colors in the electric cables.

These regulations help at a glance to understand the connection and the resolution of possible faults or failures.

Below we attach the color/cable relation for electrical installations.

1. The ground wire can be identified in several ways:
• Green cable.
• C cablegreen smell with a yellow line.
• Cable without insulation.
2. The neutral wire will be blue.
3. The phase cable can be identified in several ways:
• Any color different from neutral or earth.
• Black insulation.
• Brown isolate.
• Gray insulation.

The insulating or insulating tape is a fundamental element when making a repair or performing an electrical installation. The insulating tape will help us to protect and insulate the electrical cables from possible crossings or contacts between them or with other elements, guaranteeing that the connection is well insulated avoiding possible short circuits.
Its use is very simple, since being a flexible material allows us to apply it with comfort.
To achieve a perfect union, it is recommended that we wrap the tape covering half the cable and half over the joint, stretching the tape slightly while rolling obliquely.

• For the ground wire, colored insulation tape will be used:
• Green.
• Green with a yellow line.
• For the neutral cable, blue insulating tape will be used.
• For the cable the phase isYou can use any other color:
• Any color different from neutral or earth.
• Black insulating tape.
• Brown insulating tape.
• Gray insulating tape.

One of the basic components in most electrical circuits or electrical installations are the fuses, the fuse is a capsule (B) that has metal ferrules (C) on its ends, in which a thin filament of alloy or metal (A) characterized by having a low melting point.
The fuse is placed in a specific point of the installation, and will serve to protect said installation frompossible damage due to electrical overload or voltage.
In their normal state the filaments have continuity at their ends (C, D). This over voltage causes this filament to heat up and break (C.1, C.2), not passing electrical energy and protecting the circuit while minimizing the risk of fire.

We can find all kinds of fuses, according to their amperage, design etc.
Among the most common we can findr:

• Cylindrical fuse glass material. They are usually used in most household appliances, power supplies, etc.
• Fuses for Blade vehicles. They are the fuses that protect the electrical installation of the vehicle, usually they are of the same type and design in most vehicles, according to their amperage they have a specific color.
• Brown = 5 A
• Red = 10 A
• Blue = 15 A
• Yellow= 20 A
• Colorless = 25 A
• Green = 30 A
• Fuses for mini vehicles: It is the same as the previous one but of a smaller size.
• Fuses for Maxi vehicles: It is the same as the previous one but of a larger size.
• Midi Fuses
• Mega Fuses
• Reed fuses
• High voltage or industrial fuses

Your symbol is represented as a box and a line that crossesA line or a line is a sinusoidal shape (E).