In the case of a terminal or other device with IP44 format would result. 4 - The element to be used for the test (sphere of 1 mm in diameter) must not come at all. 4 - Do not enter the water thrown from any angle to an average of 10 liters per minute and a pressure of 80-100kN/m for a time not less than 5 minutes.

hen we talk about IP code (International Protection) we talk about an international standard (IEC 60529) which classifies the protection against external factors, solid or liquid, that has a component or electronic device; LED strips, controllers, meters, security cameras, etc.

This alpha-numerically standard has been designed to sort different levels of protection. Nomenclature starts with IP followed by two numeric values.

- Example IP68:

The first value ranges from 0 to 6 and indicates the protection against solid agents. In this case, strong protection against dust.

The second value is between 0 and 8 and indicates the protection against liquid agents. In this case the complete and prolonged immersion during the time specified by the manufacturer.

We could say that the larger the number is greater IP protection has a device.

In below table, we can see different IP protections levels available.

IPXX	First digit (IPxx)	Second digit (IPxx)
0	Unprotected.	Unprotected.
1	Protection against objects of> 50 mm diameter.	Protection against vertically dripping water.
2	Protection against objects of> 12.5 mm diameter.	Protection against inclined drip water up to 15°.
3	Protection against objects of> 2 mm in diameter.	Protection against water projected from any direction, up to 60°.
4	Protection against objects of> 1 mm in diameter.	Protection against splashing water any direction.
5	Ingress of dust is not entirely revented, but it must not enter in sufficient quantity to interfere with the satisfactory operation of the equipment .	Protection against water jets.
6	Dust tight.	Protection against strong jets of water.
7		Protection against complete immersion up to 1 meter for 30 minutes.
8		Protection against complete and prolonged immersion.

When carrying out an electrical installation or electrical circuit several factors must be taken into account, one of them is the selection of the appropriate cable. According to the installation and the use of the same we can find different diameters that support different loads. The cable section will also help us not to overheat our installation, since the larger the section, the greater the thermal resistance.
In the following table poWe can see the corresponding load supported for the different sections of cables.

The socket is the part that allows connecting the bulb to the socket. There is a wide selection of bushings for different types of bulbs. The nomenclature for each type includes 1 or more letters (type of lampholder), followed by 1 or more numbers (diameter of lampholder).
Example: The bush E27 would correspond to the type of thread E (Edison) of 27mm in diameter.

• E12: Diameter of 12mm, this is a tamYear smaller than the most commonly used standard E27.
• E14: It is the second most common cap, only varies a little of the E27, with a diameter of 14 to 17 mm. It is normally used for bulbs or lamps.
• E27: This is the most common cap. It has a thick cup shape with thread to be able to adapt to the connector. It measures 27mm wide.
• E40: Has a diameter of 40 mm, it is the largest thread of this tIpo.
• G4: With a distance between pins of 4.0 mm. It is a type of cap that is frequently used in appliqués, ceiling lamps and hanging lamps.
• G5.3: With a distance between pins of 5.33 mm. The GU 5.3 socket format is a format widely used in small led floodlights with transformer. Usually used in halogen lamps and dichroic halogens.
• GY6.35: With a distance between pins of 6.35 mm, trOf a model similar to the previous one.
• G9: With a ditancia between pins of 9,0 mm. Usually used for ceiling lamps and hanging lamps.
• G13: With a distance between pins of 12,7 mm. It is used in fluorescent tubes.
• GX53: With distance between pins of 53 mm. Its most common use is the installation in light bulbs to illuminate furniture or unusual places. It does not need transformer.
• GU10: With a distance between10 mm pins. The GU10 bushing shape is a widely used format in small transformerless LED spotlights. Usually used in dichroic halogen lamps.
• B22: Type of bayonet connector used in countries such as Africa, India and Ireland.
• MR16: Its use is normally limited to 12V halogen lamps.

As it is common in installations we can find a standard of colors in the electric cables.

These regulations help at a glance to understand the connection and the resolution of possible faults or failures.

Below we attach the color/cable relation for electrical installations.

1. The ground wire can be identified in several ways:
• Green cable.
• C cablegreen smell with a yellow line.
• Cable without insulation.
2. The neutral wire will be blue.
3. The phase cable can be identified in several ways:
• Any color different from neutral or earth.
• Black insulation.
• Brown isolate.
• Gray insulation.

The insulating or insulating tape is a fundamental element when making a repair or performing an electrical installation. The insulating tape will help us to protect and insulate the electrical cables from possible crossings or contacts between them or with other elements, guaranteeing that the connection is well insulated avoiding possible short circuits.
Its use is very simple, since being a flexible material allows us to apply it with comfort.
To achieve a perfect union, it is recommended that we wrap the tape covering half the cable and half over the joint, stretching the tape slightly while rolling obliquely.

• For the ground wire, colored insulation tape will be used:
• Green.
• Green with a yellow line.
• For the neutral cable, blue insulating tape will be used.
• For the cable the phase isYou can use any other color:
• Any color different from neutral or earth.
• Black insulating tape.
• Brown insulating tape.
• Gray insulating tape.